Mwi

[VOIPoTim]

Hey Guys,

I'm told by VOIPoRay that MWI is now in place. It should be working, but may need a little more testing.

Currently it will send the light notification at the time a message is received and also will update hourly.

If you use this feature, please test it.

[usa2k]

[I have a phone problem where I guess I need to submit a ticket. (Incoming has no audio - outgoing is fine.)]


But ON-TOPIC:
Calling the VOIPo number from the VOIPo makes the Voicemail kick in right away.
Leaving a message, then hit pound as it suggests gets an immediate busy tone.
(It would be nice if it said goodbye since no options are offered.)
The phone gets a stutter tone and the Grandstream blinks a green light.
There is no VMWI to the Uniden Handset like Packet8 sends.

Deleting the message clears the stutter and green blinking light.

I failed to get a text message from VOIPo like I had setup.
I failed to get an email with attachment like I had setup.

[VOIPoTim]

[I have a phone problem where I guess I need to submit a ticket. (Incoming has no audio - outgoing is fine.)]


But ON-TOPIC:
Calling the VOIPo number from the VOIPo makes the Voicemail kick in right away.
Leaving a message, then hit pound as it suggests gets an immediate busy tone.
(It would be nice if it said goodbye since no options are offered.)
The phone gets a stutter tone and the Grandstream blinks a green light.
There is no VMWI to the Uniden Handset like Packet8 sends.

Deleting the message clears the stutter and green blinking light.

I failed to get a text message from VOIPo like I had setup.
I failed to get an email with attachment like I had setup.

Have you tested this with an external call (like from cell) or was this only for a call from within our network?

Seems to be working on external for me, so wanted to confirm that maybe it's the way things are setup for in network.

[usa2k]

I have a phone problem where I guess I need to submit a ticket.
(Incoming has no audio - outgoing is fine.

I *think* my audio issue was my 2nd registered device for the same number.
Seems to work with that offline

[VOIPoTim]

I *think* my audio issue was my 2nd registered device for the same number.
Seems to work with that offline

Glad to hear.

One suggestion with that that is for everyone with multiple devices.

Please make sure that if you have multiple ATAs on your network that they are using a different SIP port.

We run on ALL ports in the range of 5060-5080. If you already have something in 5060, register to us using an alternate port.

[fisamo]

vPanel seems to have the voicemail messages now, but it's not quite as instant as MWI. In fact, the delay seems somewhat variable. (I called, left a message, tried refreshing immediately--saw nothing. Called again, logged out of vPanel, logged in. Saw the SECOND VM message, but not the first. Called a few more times, was logged out of vPanel, waited several minutes, logged in, all messages there.) I also set forwarding to my email account. In no case did the attachment come through--gmail says that all the attachments have 0k length.

When I click on the phone number in the vPanel listing of the messages, I presume it's supposed to play the message, right? I get nothing--no launch of a media player, no audio. Is this feature supposed to work now?

Messages don't seem to clear from vPanel right away after being deleted over the phone. I deleted the msgs by touchtone, refreshed vpanel screen, and the messages were still listed. Logged out of vPanel and logged back in. Messages were still there. However, after a few minutes (we're talking one or two) and another log-out/log-in, the messages were gone. To me, this kind of delay is acceptable.

[Montano]

Working fine for me and my Uniden via a PAP2T. The notification was instant and I have stutter tone and light indicator on my phone.

[Montano]

Tim, I can also verify that no email or sms message is being received. But I have never received an sms message from VOIPo voicemail. I used to get email notifications, but have not in a while. We (you) even added AT&T to the sms list but still nothing. I chalked both things up to it being beta. I had reported both issues quite a while back.

I have tested from both internal and external lines.

[fisamo]

The voicemail on vPanel seems to be out of sync with the actual VM system now. For a while on my 1199 line, I had about 10 messages in the inbox that I never bothered to listen to. They were all listed in the vPanel, no problem. I tried using vPanel to delete them, but they were still there when I dialed into the VM system. After deleting them with the VM system, they were gone.

Now, I've placed a few test calls to the line and left messages. They seem to be accepted just fine (and when I hit the pound key, Allison says, "Thank you." ) I know the messages are there, because the MWI light (on my ZOOM) comes on immediately, and I get stutter tone. When I log into the system by touch tone, I can get the messages.

It's pretty amazing how quickly the MWI light updates--when leaving the first message, it comes on just as I hit the # key; when deleting messages, it goes off as I log out of the VM system.

FWIW, I still have the problem that when setting failover to forward to a number (at least a SIP address), calls do not go to VM. After ringing the specified number of times, the call is sent to the failover phone number. With a SIP address, it seems to just get dead air after the number of rings...

[VOIPoRay]

The voicemail on vPanel seems to be out of sync with the actual VM system now. For a while on my 1199 line, I had about 10 messages in the inbox that I never bothered to listen to. They were all listed in the vPanel, no problem. I tried using vPanel to delete them, but they were still there when I dialed into the VM system. After deleting them with the VM system, they were gone.

Now, I've placed a few test calls to the line and left messages. They seem to be accepted just fine (and when I hit the pound key, Allison says, "Thank you." ) I know the messages are there, because the MWI light (on my ZOOM) comes on immediately, and I get stutter tone. When I log into the system by touch tone, I can get the messages.

It's pretty amazing how quickly the MWI light updates--when leaving the first message, it comes on just as I hit the # key; when deleting messages, it goes off as I log out of the VM system.

FWIW, I still have the problem that when setting failover to forward to a number (at least a SIP address), calls do not go to VM. After ringing the specified number of times, the call is sent to the failover phone number. With a SIP address, it seems to just get dead air after the number of rings...

The VM in VPanel should now be back in sync. My account is working now. Please test and see how it goes.

The issue with the call not going to VM on a failover number should be addressed withing the next few days.