Hardware Update

**VOIPoTim** · 10-15-2008 04:24 AM

Originally Posted by usa2k

Tim

Have you seen this thread?
http://www.dslreports.com/forum/r212...er-doesnt-work

Yeah I'm pretty sure this is just a network setup issue likely what the last poster said with the IPs conflicting.

It works fine behind router for me at office and home.

**NY Tel Guy** · 10-15-2008 11:43 AM

Originally Posted by VOIPoTim

Yeah I'm pretty sure this is just a network setup issue likely what the last poster said with the IPs conflicting.

It works fine behind router for me at office and home.

So Tim, is the fact that I have a 286 and cannot do 3 way calls or toggle back and forth between 2 calls (like on call waiting) a non-functioning feature of the 286 that is corrected with the 502 or might I just have a "bum 286" that needs a firmware update etc?....

**scott2020** · 10-15-2008 11:54 AM

I also have the 286 and see the same problem with the toggle. I swear though I have been able to call home, wife flashes over to pick up the call, we talk for a few, and she goes back to the first call. But, I just tested it with her and it doesn't work. We were on the first call, flashed over to the second call, then flashed back to the first and had just dead air on both calls. We had to hang up and re-dial.

Scott

**dswartz** · 10-15-2008 12:45 PM

Sounds like other people have had this issue:

http://forum.voip.com/viewtopic.php?id=5347

**NY Tel Guy** · 10-15-2008 12:52 PM

Originally Posted by dswartz

Sounds like other people have had this issue:

http://forum.voip.com/viewtopic.php?id=5347

Thanks for that link. Must be an issue with the GS 286.

**dswartz** · 10-15-2008 01:08 PM

Quick question: I was looking at my HT286 (it registers to my asterisk system, not voipo's servers). I had the same issue as you guys, but never got into looking as to why. Here's an issue: HT286 has two ways of doing 3-way: "bell style", where you diddle the flash hook like you guys do, and the other way, where you press flash to put A on hold, dial '*23' followed by B's number, and when (if) they answer, press flash again. NOTE WELL: the default is mode 2, NOT mode 1

I haven't yet tested this (I'm at work right now), and I'm not sure you guys can (isn't the ht286 locked? do any of you have BYOD credentials and can prove/disprove my hypothesis?) If this is it, it's a simple voipo config change they can push out to you all.

**NY Tel Guy** · 10-15-2008 01:17 PM

Originally Posted by dswartz

Quick question: I was looking at my HT286 (it registers to my asterisk system, not voipo's servers). I had the same issue as you guys, but never got into looking as to why. Here's an issue: HT286 has two ways of doing 3-way: "bell style", where you diddle the flash hook like you guys do, and the other way, where you press flash to put A on hold, dial '*23' followed by B's number, and when (if) they answer, press flash again. NOTE WELL: the default is mode 2, NOT mode 1

I haven't yet tested this (I'm at work right now), and I'm not sure you guys can (isn't the ht286 locked? do any of you have BYOD credentials and can prove/disprove my hypothesis?) If this is it, it's a simple voipo config change they can push out to you all.

Thanks.
I was able to get into my 286 and Bell style was not selected. I selected, saved and re-booted. When it came back - Bell Style was once again de-selected.

There is an issue with some of the 286's where no changes are saved even if you change them.
I think I own one.
Looks like I'll be catching the "502" train home shortly.....lol

And thanks.

**scott2020** · 10-15-2008 01:44 PM

I did a quick search and found several people with this problem since 2006 or longer. It doesn't seem possible they can put "call waiting" down on their feature list in this condition. Sure, it lets you pick up the 2nd call, but it is almost useless if you can't go back to the first or toggle.

For "mainstream" people coming from the POTS world, this will be expected. I hope the new ATA resolves this.

I have the same question as mentioned already. Will I get a new ATA for this reason? Thanks again.

**VOIPoTim** · 10-15-2008 01:55 PM

Well first we need to work through troubleshooting for anyone having issues to determine if it can be fixed by a firmware change.

In tests today, call waiting is working fine on our test 286 units. It is a known issue on some units that they had a switching issue, but it's firmware specific. If you're seeing it, open a ticket ideally with the firmware version if possible (just access the IP in a browser and use password 123 to find it) and it should be able to be resolved by upgrading. The only thing that is not going to change with the 286 units is that they play a soft ring vs beeps for call waiting.

For 3 Way Calling, you do need to dial *23 before the number when dialing the 2nd party. As long as you do this, it should be fine. Again, if you have issues with this, open a ticket and we'll check on the firmware, etc.

So the bottom line is if you're having issues, open a ticket and we'll go from there. If there's a legit reason for a swap that we can't solve otherwise, we'll do it. We have to try to resolve it via firmware first though.

Still way too many people e-mailing wanting a new device for no real reason....